What Car Battery Should You Choose? Absorbed Glass Mat (AGM), Gel Or Wet Cell

An electrical problem that doesn’t let your car start and leaves you stuck in a parking lot or some place away from the fix that’s needed is an unwanted problem we all do our best to avoid. So what can you do to lessen the possibility of a possible unwanted situation that involves an electrical system crash in your vehicle?

First of all make sure you spend double the money on a good car battery. A lead acid battery can cost between $75 to $125 dollars. The only reason liquid lead acid batteries are the most commonplace is liquid lead acid batteries were first developed in 1859 and they are the least expensive in today’s world of automotive engine starting sources. In 1971 the sealed liquid lead acid battery was created that made it maintenance friendly.

VRLA (valve regulated lead acid) batteries include gel and absorbed glass mate which are not liquid. Gel batteries are as the name applies which is a “Gel”. AGM batteries are silicate glass fibers mixed with boron and formed into a mat that holds the electrolyte. Non liquid gel batteries were created in the late 1920’s and lead to the creation of the “Absorbed Glass Mat” batteries in 1957. The AGM (absorbed glass mat) battery was put into production in 1972 but mostly used for military applications and non vehicle applications like boats, motor homes, motorcycles and electronics. Nowadays you see more AGM batteries becoming available for use in production cars. AGM (absorbed glass mat) batteries can cost from $160 to $250 but have more advantages over liquid lead acid batteries.

AGM batteries are basically used in applications where the use of the vehicle is only used now and again as in boats and recreational vehicles. The non use discharge rate is much lower in non use applications than liquid lead acid batteries. The charge rate is much faster also. Some automotive manufacturers are installing AGM batteries as their standard new car power source because of today’s higher vehicle power consumption. BMW right now is known to be the first to install AGM batteries in their 2007 models because of computer functions and braking.

AGM batteries are much better than liquid lead acid batteries but the downside of AGM batteries is you don’t overcharge them. They will charge faster with a normal output alternator up to 14.5 volts and a high output alternator is not needed. When an AGM battery is used in a non use vehicle a solar panel is recommended with a trickle charge. AGM batteries will go bad if charged over 14.5 volts. Most problems with charging AGM’s are in sports vehicles due to the rough environment they are used in. Toss away your old plug in garage battery charger and get a new one that maintains “Voltage” instead of amps. An AGM battery charger will sense a very low voltage in the battery and will start the recharge whereas an old charger does not sense low voltage and will not charge the battery.

These batteries are used in military vehicles that sit in storage for many years and start up after years in storage with no problem. I’ve read stories online where people have left their AGM batteries sitting in their garage for many years and they have retained their full charge. I use AGM batteries in my vehicles and disconnect the negative cable in the one that I don’t use that often anymore and it starts right up when I run the engine occasionally. I’ve read complaints about the AGM failing often but that’s only because of bad practices with them or using them in systems where the charging exceeds the recommended level. You can leave these batteries sitting for long periods of time without charging them but it’s recommended that a solar panel with an extremely low trickle charge be used when not in use. Again I will say from my own experiences is to disconnect the negative cable to the battery when not in use.

The AGM vs Gel and the wet cell? The AGM has thicker plates that tend to not warp that easily during deep discharges and resist sulfur buildup’s that destroy a wet cell battery. Wet cell batteries usually go bad after 4 years if they make it that length of time. The life expectancy of the AGM battery can be up to 10 years if not overcharged. Gel cell batteries are great for sports vehicles but tend to charge slower.

The Winner Is, “Absorbed Glass Mat” if you learn how to take care of them properly.

Find all the info that you need about " Iran visa mysteryofiran " at mysteryofiran.com
Posted in homepage | Comments Off on What Car Battery Should You Choose? Absorbed Glass Mat (AGM), Gel Or Wet Cell

The Seven Wonders of the World

The world around is filled with all kinds of wonders and we can gaze at them only by opening our eyes and our hearts. After all you need to believe in magic to be able to believe it. However, if you’re someone who is a bit on the cynical side, we bring to you a list of the wonders that exist all around the world. If you are a fan of archeology, history or travelling you’re definitely going to enjoy this article. Oh and if you plan to travel after reading this, don’t forget to look into Cathay Asia Airlines.

1. The Great Pyramid of Giza
The crown jewel of Egypt and the only surviving architecture from the original Seven Wonders of the Ancient World, this pyramid is truly a sight to behold. This pyramid is said to be built as a tomb to the Egyptian Pharaoh Khufu. The building is approximately 480 feet tall and was the tallest building in the world for more than 3800 years. This pyramid when built was outlined with a limestone casing which with time got destroyed. Now you can only see the casing near the bottom of the pyramid whereas the top exposes us to the inner lining of the pyramid.

2. Petra, Jordan
Petra is often called the city of rose due to the red colored stones that it is made of. This beautiful hidden city is famous for its architectural grace and the water conduit system. Even though the city is located in Jordan, it was actually discovered by a Swiss explorer in the early 19th century. This place is also said to have structures that are more than 2000 years old.

3. Christ the Redeemer, Rio De Janeiro
This miracle took a total of nine years to be constructed due to the its location on the top of a cliff. This is the third largest statue of Jesus in the world. The raw materials for this statue were actually imported from Sweden. This beautiful statue was actually constructed as a sign of peace, to show that Christ loves everyone.

4. The Great Wall of China
This wall that stretches over 8000 kilometers was built over a period of 2000 years and renovated over time by many different Chinese dynasties. It is said that millions of people died while building the wall and that they’re buried within the Wall’s foundations. The Wall is also famous because it is the only structure on Earth that can be seen from the moon without any aids. Fascinating right? Go check it out yourself!

5. The Colosseum
This fighting ground of the roman gladiators took 8 years to build and was designed by the Roman Poet Virgil. The Colosseum has more than 80 entrances and can house 50,000 people at one time. It receives millions of visitors every year and is therefore the biggest tourist attraction in Rome.

6. The Leaning Tower
This beautiful tower located in Pisa is famous because of the way it inclines with height. The architecture has been constructed in a way that makes it feel tilted. If you’re ever in Italy, this is a must place to go to.

7. Taj Mahal
Constructed by an emperor in the memory of his beloved wife, this palace is a symbol of love for the entire world. The intricate architecture and carving inside this Mahal will make you fall in love with it. And if you don’t believe us, why don’t you go see it yourself? All you have to do is book your ticket using Cathay Asia Airlines.

Posted in homepage | Comments Off on The Seven Wonders of the World

Brainstorming To Start A Small Business – Questions To Answer

Hello readers and potential future entrepreneurs. I understand the feeling; desire to create, operate, and succeed. Throughout my professional career, I have learned that there are numerous steps that must be taken in order to organize opening and operating a small business. I have put together a few questions which aspiring entrepreneurs should, at the very least, consider reading over. There are many questions that may arise with opening a small business, and I will address a few of those questions briefly in the following list of questions one may ask while brainstorming.

What type of business do you want to open? There are various business endeavors an entrepreneur could involve themselves in. It all comes down to what knowledge one has, or is willing to obtain. Are you a restaurateur? Repairman? Plumber? Home health / assistance? Do you have experience managing or working at such establishments? Do you need formal education from an institution? Will you work as a sole proprietor, or a partner / member? Research limited liability corporations (LLCs) in addition to sole proprietorships and partnerships. S corporations are another option, but they are for business with stockholders, and may not be right for your particular business application.

What kinds of licensing and/or permits are required? Each business will have different licensing requirements; it all comes down to what the entrepreneur ultimately chooses to do. A restaurant would need food safety licensing in addition to basic business licensing, and if alcohol is on the menu – there is another permit the entrepreneur would need to legally sell alcohol on the premises. Repair oriented businesses would need at least the business license to repair, but if they sell parts as well, they would need to have “retail” listed on their business license in addition to “repair”. Health care services require at least formal education and licensing as an LPN, RN, or one of several other health care related licenses. Be sure to check your state’s laws to ensure what is necessary to operate your type of business.

What training / education / certifications are required to legally run this business? We touched upon this in licensing / permits, however there is much more involved than the required licensing. For example, one cannot operate a vehicle collision repair business without the knowledge of performing those types of repairs. There are schools that can be attended to learn what must be learned to effectively operate nearly any kind of business. However, there are also businesses where experience is enough to operate effectively without needing any formal education (lawn care, house cleaning just to name a couple). Also, there are certifications for training in nearly, if not all, care industries.

Does this business require a storefront? Retail establishments will undoubtedly need a storefront. Bear in mind, retail business will have a much larger initial investment than a service based operation. That initial investment is inventory. Some service businesses may not need a storefront to operate, as much of the service performed could very well be on-site. If a storefront is necessary, be sure to consider delivery or on-site service if it is feasible for your operation.

How much will it cost? This number will vary wildly based on the type and size of business you are planning. For smaller businesses, this number could be as low as $200 for a license and/or permit, or as high as a million dollars or more. Obviously, inventory is very expensive, and so are specialized tools for performing extremely precise work. Calculate the expected opening and operating expenses. Determine what size storefront is needed (if applicable), and research local commercial realty properties, locations, and prices. It is absolutely cheaper to rent in the short-term, although the thought of owning property that is paid off is very tempting. Prices on most things will vary based on your location. Employees are another cost, if your business warrants employees. When employees come into the equation as opposed to sole proprietors or partnerships, one must add extra insurance for the business (unemployment insurance comes to mind). Check with your selected insurance company for which types of additional coverage are required, and if offering health insurance can be done reasonably. Those employees will also need to have taxes paid on their wages – part from the employee’s paycheck and part from the company. Another potential cost is repayment of loans, if you don’t already have the capital needed to open your business. Basic operating expenses are not to be forgotten, as heating/cooling, Internet connectivity, and utilities will be regular expenditures for any storefront. On-site service operations cost very little when compared to a physical storefront.

How can an individual pay for this? If you do not have the funds available, which is very common, applying for loans is a way to attain funding. Be sure to have a business plan with projected expenses and revenues. There are other ways to gain funds for a business. Look into grants. While they are not very common, they are a potential source for assistance nonetheless. If many people believe in your dream, one could possibly acquire donations from those individuals.

What about accounting? Bookkeeping is a necessity – research which accounting/bookkeeping software would work best for the type of business you are planning. Point-of-sale (POS) systems are needed for “ringing up” and selling inventory or goods to the customer. POS systems keep track of sales, sales taxes, employee labor dollars spent, and many other items. If you are apt at creating spreadsheets, you may be able to keep track of your own inventory depending on your particular business model.

I hope this brief listing of questions and potential answers has been of assistance to aspiring entrepreneurs. Although there are countless successful entrepreneurs who have little or no formal education in business, it is never a bad idea to research courses regarding administration and management. Be sure to take a look at the Small Business Administration’s website at http://www.SBA.gov for more helpful information.

The author, Johnathan Baker, is an educated entrepreneur, with over ten years of experience in small business administration and management. Opening any type of business is no simple task, as many things must be considered. With experience opening, operating, and managing small businesses, the author aims to help aspiring entrepreneurs in realizing their dreams. While the questions are not all inclusive, they are, at the very least, a good bit of information to consider throughout the beginning processes of opening a small business. Take the information provided and begin or continue working on your business plan on the road to entrepreneurship.

Posted in homepage | Comments Off on Brainstorming To Start A Small Business – Questions To Answer

Must-Know Facts About Armored Recovery Vehicles

Various kinds of military vehicles are used in used in war-torn areas or places where conflicts are present and continuous. One of the most common types of specialized vehicles you will see in such areas are armored recovery vehicles.

An armored recovery vehicle, also known as Armoredownload-12d Repair and Recovery Vehicle or ARRV, has the primary purpose of recovering and/or repairing damaged or inoperable vehicles right in the battle field.

These specialized vehicles were first called Salvage tanks during World War I. It was only during the Second World War that people began calling them recovery vehicles.

The earliest versions of these vehicles were usually equipped with repair tools or with winches of heavy-duty to release the stuck vehicles. However, the latter generations or newer models were outfitted with a type of crane attached to the A-frame – a feature which could perform the task of lifting heavy parts from disabled vehicles, such as the engine. In addition, during the post-war period, various great alterations and improvements were made in these vehicles. Some of these capabilities include the improved ability of these vehicles to carry an extra engine to replace a non-working on the field and fuel pumps which allow the easy transfer of fuel. They can also carry anchors which can be utilized as stabilizers in heavy lifting situations.

In the past, recovery vehicles were usually derived from battle tanks of other armored fighting vehicles. Today, most manufacturers build them from the same type of material or vehicle they will most likely or frequently recover on the war field.

Although recovery vehicles are one of the sturdiest and strongest specialized vehicles around, they also have limitations. In cases where the work of a recovery vehicle is not possible anymore, tank transporters will have to be used. Tank transporters have the mission of transporting the tanks on the war field for longer distances, to reduce road damage, save fuel, or to recover them from the war field. Certain types or models of tank transporters are equipped with special protection, in case they have to make their way up to the first line.

Armored recovery vehicles are important types of specialized vehicles to have and use where fighting, especially with the use of artillery, is consistently present. To make sure that you can make the most of your vehicles and that the operator and passengers will be safe during transport, make sure that you purchase them only from a well-known and trusted automotive manufacturing company.

Posted in homepage | Comments Off on Must-Know Facts About Armored Recovery Vehicles

Cellular Or Mobile Phones: How Are They Affecting Children And Us?

I am sure you are using one of them, like almost everyone else doe’s including me. As you become aware about some things, most likely you will be making changes the way you use a cellular phone from the information and awareness you be reading about.

There are as many as over 7 billion mobile phone subscriptions worldwide. Continued research to clarify any health risks coming from cell or mobile phones is ongoing. The first thing to come to mind is electronic radiation such as changes to sleep patterns and brain activity. Lots of evidence demonstrates that radiation from cell phones is a real danger.

Many different researches over years have confirmed that long-term exposure to cell phone radiation is a significant risk to health. Such findings of course are strongly denied by the other side of that argument, depending on which side of the argument you listen to. Debates like this have been ongoing for years and most likely will never be settled. After all, why would designers and manufacturers admit to any danger coming from phone usage? This would certainly kill the goose that lays the golden eggs!

The international agency for research, which is part of the world health organization released a statement over five years ago and declared cell phones a class B Carcinogen.

Long Term Exposure: How Long Is Too Long?

Whatever the brand name, I Phone, blackberry, android, tablets, Smartphone’s or just a basic flip phone has revolutionized communication in the 21st century. Some people spend as much as 2 ½ hours or more on the phone daily. Because cell phones are providing an efficient and easy way to communicate, but at the same time this can also take a toll on health.

The possible effect of a long-term heavy use of any mobile phone and the length of each call matters. The amounts of time people use cell phones are important factors which enhance the health related risk. The amount of radio frequency energy from a mobile phone use being released depends on different factors, such as distance from face and ear, the type of phone used, and the distance between cell phone towers.

What these findings are telling us: Make your conversation on a cell phone as short as possible or better still use a hand free device which places more distance between your head and the phone. Turn off the phone when not in use. Use the speaker phone when possible. Keep your phone away from your body as much as you can. Never use your phone while driving or even worse texting; this puts you and others in a potentially dangerous situation.

Children Are More Vulnerable

Children have the potential being at greater risk and affected in different ways. The brain of a child is not fully developed until the age of around 20. This makes any exposure to electronic radiation and radio frequency more dangerous for children than for adults. The other issue which affects a big percentage of children as well as teenagers is eye vision. Looking at mobile screens, what is it doing to kids’ eyes? Almost at any age children love playing with smart phones but what are the long-term effects?

Unfortunately some people are using such gadgets as baby sitters for the children without being aware of the damage it does. Children like to watch things close up on screen which is contributing to spike in becoming short-sighted. Studies have shown there is an alarming increase that affects many children between 10 and 12 years old and the amount has doubled over the last decade. The fact is: The more kids watch things close up on screen, the more they put their eyes in danger.

It is most common for children to develop myopia which gives a blurry long-distance vision. Myopia can also increase the risk of other eye problems in adulthood as well, including cataracts and blindness. However, most of the myopia cases are as young as six and 15 to 18, of course genetics play a role in severity in this.

As a guide, reduce screen time to as little of 2 hours per day from 2 to 5 year olds. There should only be a small increase of time allowed for older ones. Actually in Taiwan, if a child under the age of 2 has been found with a tablet or playing with any cell phone the parents will get a heavy fine.

Children who spent more time outdoors in fresh air and sunshine have a far lower rate of myopia. Limit the screen time, encourage kids to spend more “green time” hours in nature outdoors for better health. Make sure to include a colorful veggie diet from leafy greens which contain lutein, this is known to help eye sight and vision.

In General Common Sense Applies

A cell or mobile phone for most people has been one of the most revolutionary developments in time. It is a great communication tool being able to carry it with you wherever you go. It is a good security and emergency device that can save lives. So, what is wrong with all of those gadgets?

Could it be just the one who is using it creating that problem?

There are too many people going to the extreme and don’t know what is any longer normal or reasonable. That also applies to our food intake, beverages, including alcohol, and tobacco etc. All of those are not, or less harmful if used in moderation. If only used for short time this also can apply to cellar or mobile phones, and can reduce the risk factor as much as eighty percent.

Posted in homepage | Comments Off on Cellular Or Mobile Phones: How Are They Affecting Children And Us?

Stability, Predictability, Consistency, and Standardization in the Flow of Commerce

The best of all possible worlds is for the government to stay out-of-the-way of commerce, industry and business, and very rarely institute regulations. There are some times when government and businesses, industry associations should collaborate for the sake of standardization, but again, very rarely. The tendency to allow industry collusion, create monopolies, duopolies or quasi-cartels is just too easy. Further, once you create one regulation it’s hard to prevent the add-on affect, the temptation is just too great to add exceptions, additions, clarifications as lawyers, unions, and consumer groups work to lobby legislators to intervene with the regulatory apparatus.

A few years back this was a big conversation at our Think Tank, and one think tanker Andrew stated: “I would have to agree that businesses do need some form of standardization, but we must also understand several concepts! A business must have the capability to micromanage for maximum efficiency. I believe states should be granted the power to standardize businesses, not the federal government.”

Okay but, where I see the definite need for standardization are with things like Internet Protocols, railway track width, freeways for intrastate travel, airport runway markings, frequencies used in communication, food safety, etc. In a big state like TX you could get away with doing almost everything counter to the overall prevailing way of doing things, it’s practically large enough to be its own country, and some Texans would prefer it to be still. Pretty independent minded, even with the population’s mindset of succession from the union. It even has its own electrical grid.

Still, with regards to the flow of energy, transportation, distribution, communication, currency, etc. we need standardization. And to the point of having each state decide, what about every county, every city, or every HOA, down to every person, where do you stop the breakdown of centralized standardization.

The argument for state level standardization could be argued against by someone who is a County Supervisor telling the State to go to hell, we want to do it our way, especially a county like the County of Los Angeles, with 16 million people in it, also larger than most countries. How about a city telling the county where to go, again as an example, let’s take the City of Los Angeles VS County of Los Angeles, see the point.

And realize I am not making an argument for a global government here, but we also need some standardization there too, for aviation, which we do have, maritime, trade rules, and having the Central Banks work together so no one Central Bank doesn’t destroy the entire global economy. See that point. We need SOME standardization, but we MUST retain regional variation. We do this at the Global Level, but we don’t do it enough at our Federal Level with regards to the states in the US and that’s why we have issues now. Think on this.

Posted in homepage | Comments Off on Stability, Predictability, Consistency, and Standardization in the Flow of Commerce

Sensible Manufacturing and the Ultrasonic Flow Meter

The Manufacturer MX Awards

Each year The Manufacturer MX Awards aim to recognise great achievements in the industry. Entries are invited for a number of different categories, with the ultimate title of ‘Manufacturer of the Year’ presented to a company that is strong across the board.

The winner of this year’s ‘Manufacturer of the Year’ title was announced in November and Dura Automotive took home the award. The company also returned to the office with awards for ‘People and Skills’, ‘World Class Manufacturing’ and ‘Sustainable Manufacturing’, so it was well worth attending the event!

Investment in Employees, Quality and Sustainability

Dura Automotive are an international company that design and manufacture control systems for the automotive industry. They may be a large operation, but the awards they won clearly illustrate what it takes to grow a successful business; investment in employees, quality and sustainability.

If you take a look on their website, you will see that their objectives are to ‘inspire drivers, customers, our people, the competition and stakeholders through innovation and performance’.

They understand that in order to deliver full customer satisfaction, they need to deliver high quality products. To do that, they need to stay ahead of the competition with innovative ideas, products and processes, staff training and development opportunities and a positive, customer focused vision. In addition, they understand the importance of integrating sustainability into every aspect of their business.

Sustainable Manufacturing

Sustainable manufacturing focuses on minimising the negative outcomes of production. The overriding aim is to lower the environmental impact of manufacturing and distribution, yet the real benefits to business come from the fact that in working towards sustainability is a process of continuous improvement.

Many manufacturers have been incentivised to take action. On the receiving end of Government initiatives or in a bid to reduce energy, water and waste management costs, more companies have been willing to consider sustainable options. Whilst they may have started off thinking of this as a tick box exercise, the real benefits of taking action soon become apparent. Huge savings have helped many companies to remain competitive in the global market, have paid for other investments or have boosted profits.

Flow Monitoring

When it comes to water and energy use, flow monitoring has proved valuable in running processes at optimised levels, improving quality control, minimising waste and reducing downtime due to problems in the process. This has supported significant cost savings in storage, processing, waste management and utility bills.

By investing in low cost ultrasonic flow meters, which retrofit to the exterior of pipework, flow monitoring can be straight forward to implement. Calibrated to the specific flow range of the liquid or gas that passes through the pipe, the ultrasonic flow meter provides data that quickly identifies when abnormal flow rates are detected. This acts as an early warning system, so the issue can be quickly identified and rectified.

The ultrasonic flow meter also supports the optimisation of the process, which can be highly effective in quality control. This has been widely used to reduce waste batches and waste management costs in food, pharmaceutical and automotive industries, to name but a few.

All of these potential cost savings from an affordable ultrasonic flow meter certainly justify investment in monitoring technology. Other low cost devices including tap aerators and rainwater harvesting systems have also helped UK businesses to gain a lot more than environmental credentials.

Recycled Materials

Another area in which Dura Automotive have invested is in research and developments around the use of recycled materials in their products. When manufacturers consider reusing materials rather than raw supplies, it can present a number of challenges. Being open minded to these challenges can lead to innovative thinking, fresh ideas and approaches which could open up new avenues for the product or company.

The use of recycled materials does depend on sufficient quantities being provided by a reliable source. Having said this, if a large scale operation such as Dura can find viable alternatives to raw materials, then a bit of research could lead to suitable supplies for smaller businesses.

There is often a cost in processing the material to ensure it is of a suitable standard for reuse. Companies may need to explore partnerships with other companies and other collaborative approaches to ensure that cost effective and convenient options are found.

Sustainable Advantages

Like Dura Automotive, the majority of the other manufacturing award winners also placed considerable emphasis on sustainability. If you want to see your company going from strength to strength, a greener approach could deliver many tangible advantages.

Posted in homepage | Comments Off on Sensible Manufacturing and the Ultrasonic Flow Meter

The Best Places To See If You Go To Italy

Ravioli, Tiramisu and lush red wine- we all know how amazing all of these things are in Italy. But another thing that Italy is famous for are its beautiful and renowned travel destinations. This country is filled with remnants of the Roman Civilization and extraordinary architecture from the past. What most of us don’t know is that Italy is actually home to the largest number of UNESCO World Heritage sites. Literally everything in this country is worth seeing. But for those of us, who don’t want to or don’t have enough time to go through the whole countryside, here is a list of places you can visit to ensure you get the best of Italy:

1. The Leaning Tower Of Pisa:
This architectural beauty is actually a mathematical phenomenon that still confuses many brilliant minds. The tower of Pisa, famous for its incline is actually a wonder of the world which the most important reason for you to see it. And if you’re a fan of archeology then that’s an added bonus as well. People from all over the world come here all year round to view this. And if you’re planning to go to Italy as well make sure you book your tickets using Alaska Airlines.

2. The Colosseum:
The Roman Colosseum is also one of the Wonders of the world and is the largest amphitheatre in the world. This was created by the prehistoric Roman Leaders and is one of the biggest mementos of the Roman Civilization. It has more than 80 entrances and can house more than 50,000 people at one time. This amphitheatre was actually made as a center of sports and entertainment and has hosted several such events throughout history. However, its condition has deteriorated significantly over time due to natural disaster and climatic conditions.

3. Venice:
The city of Gondolas and water, Venice is a sight to behold for anyone who loves water. The city is famous worldwide for its beauty and the fact that it has been built completely on water. If you’re a romantic at heart, then this is the one place that you should definitely not miss out on. The structures here are comprised of over 150 canals in such an intricate manner that further enhances the beauty of the city.

4. Piazza Del Campo:
The city of Tuscany is home to one of the most beautiful and magnificent medieval squares – The Piazza Del Campo. This seems to be very common in Italy, but this structure also has some of the beautiful architecture that has been seen in the world. Twice or thrice a year a horse race is hosted here which involves circling the Piazza Del Campo and that is definitely a sight to see.

So book your ticket to Italy today using Alaska Airlines and remember to have a lot of fun and stress less holiday!!!

Posted in homepage | Comments Off on The Best Places To See If You Go To Italy

Growth Consultant: Giving New Direction To Your Business!

Earning substantial profit is the main objective of every business and for this it is imperative that your business grows in significant direction keeping pace with changing scenario. Because, if a businessmen continues to follow conventional methods of conducting business he might not be able to stay even in competition with his contenders and may lag in competition.

For the continuous growth of business it is indispensable to keep a strict eye on every change taking place across the business world. The relevance of keeping an eye on changing scenario increases more today’s age because today as an impact of globalization business operators are blessed with vast opportunities of exploring their business throughout the world in short span of time.

Days have gone back when business operators centralized their activities within a limited region, but now the time has arrived when they need to move ahead by eliminating cultural and demographic traits and transfer their orthodox business model into customer centric, best in its segment, broadening potentials of growth with feasible profits from business.

To assist the business owners in moving their business according to changing environment, growth consultants can play an incredible role in getting the infrastructure of their business keep changing in accordance to global market.

The growth consultants provide their expert advice and suggestions to business groups and may even help them in getting those suggestions implemented in organization in determined strategy. These consultants make business operators understand the drawbacks of orthodox business concepts and make them realize the changing role of not so recognized sections like women and youth in growth of an organization. They make business owners understand the contribution which they can make in exploring their business.

Moving ahead they also make them realize the changing nature of consumer behavior and how they can succeed in offering varied services and products to their multicultural consumers located in different regions of world.

The consultants of growth help business groups in:

1. Re-evaluating the core targets and models of their business

2. Identifying the gaps in their value delivery systems

3. Make them understand whether their strategies of VP communication are misfiring or not;

4. Generating the identity of their brand in accordance with values, beliefs and strengths of new worlds market place (NWMP)

5. Selecting and strengthening their value propositions and competitive differences

But sharing business details with an unknown person is not an easy task for any business operators and therefore it is necessary to get assured that information shared with consultant will stay restricted only with him and not affected by any kind of elusion. The selection of growth consultant should be done after proper research about his past experiences and knowledge.

As a general practice need of a growth consultant is felt when:

1. Growth of your business has stagnated

2. You are not able to make appropriate use of the available sources

3. When you are speculating to introduce a new initiative in market

How do growth consultants assist the business groups?

The growth consultants conduct an intensive study of every aspect related with your business on your behalf and then point out the pros and cons of your business comparing with your contenders.

After analyzing your business they find potentials of your growth keeping the changing atmosphere and making system approach for your business according to recent trends. They also help you in assessing the results and difference in your business after implementation of their recommendations. This strategy will help you in achieving desired success in your business in appropriate direction.

Posted in homepage | Comments Off on Growth Consultant: Giving New Direction To Your Business!

3D Scanning – What You Need To Know

3D scanning is a process of capturing digital information of object shape using equipment that has light or laser to measure distance between the object and the scanner. The non-destructive and non-contact scanning technology uses lines of laser light capturing the exact shape and size of the object. The fine details of even the smallest objects are captured and the process comes in handy in so many industries and fields. Some the areas that 3D scans are commonly used include automotive, manufacturing, medical and aerospace.

3D laser scanners capture thousands of points per second, allowing quick inspection of parts. It is a process that is ideally suited for measuring and inspecting contoured surfaces and also complex geometries that require lots of data for accurate description and where traditional measurement methods are impractical.

What are the advantages?

3D scanning has become very popular among business people in different fields. You can now easily find 3D scanning services for all needs you might have especially as far as accuracy and high quality productions are concerned. The popularity of the process is as a result of the many advantages it has over other traditional options. Some of the advantages that come with the process include:

1. Quick capture of all physical measurements of any given physical object; with 3D scanning, the size of the object does not matter.

2. Saves time when designing. The high definition details of objects make it possible for designers get it right with the first trail, hence saving time, even with productions that would have otherwise proved to be complex and time consuming.

3. Ensures perfect fit of parts with the first try. 3D has literally taken the guess work of production processes, especially for those dealing with prototypes and creating parts. The detailed information collected from an object is accurate and hence it is very rare to have parts that have any functional defects.

4. It captures engineering optimization that is necessary in manufactured parts. The process offers more confident to manufacturers in terms of meeting standards and any set objectives in the manufacturing process of parts. Using the scans, it has become even possible for manufacturers and designed to compare between designed and built models conditions so manufactured parts are top quality.

How does it help the design process?

3D scans are largely used in the design process of various products. Model scanning proves beneficial in the design process because:

· It increases effectiveness when working with shapes and parts that are complex

· It provides updated versions of CAD models that are outdated

· It makes it possible to replace missing parts or older parts

· It helps product designing so that someone else’s part can be accommodated

Which areas can in be used in?

3D scanning is very effective and has become a popular option in various fields including:

· Historical artifacts

· Prototyping or reverse engineering

· Entertainment industry for games, TV and movie productions

· Medical and dental

· Inspection

· Marine

· Construction and architecture

A 3D scan can prove highly beneficial in different sectors. If you do not have what it takes to enjoy the accuracy of 3D scans, you can get help from service providers who offer all kinds of scanning services.

Posted in homepage | Comments Off on 3D Scanning – What You Need To Know